? rohs lead solder exemption compliant ? industry standard half-brick ? low-cost design ? 100 c baseplate operation ? open-frame packaging ? 24 v and 48 v input versions ? input pi filter ? optional enable logic ? 1500 v isolation features has dc-dc converters provide up to 30 watts of output power in an industry-standard package and footprint. with a maximum case temperature of 100 c, the has is well suited for the most demanding telecom, networking, and industrial applications. the has features 1500 vdc isolation, short circuit, and overtemperature protection, as well as six-sided shielding. the has series is available with optional enable and voltage trim pins. please see the had series for dual-output applications. description technical specifications voltage range 24 vdc nominal 18 - 36 vdc 48 vdc nominal 36 - 75 vdc transient 100v/100ms reflected ripple 50 ma input setpoint accuracy 1% line regulation v in min. - v in max., i out rated 0.2% v out load regulation i out min. - i out max., v in nom. 0.2% v out remote sense headroom 0.5 vdc minimum output current 10 % dynamic regulation, loadstep 25% i out pk deviation 4% v out settling time 500 s voltage trim range 10% short circuit / overcurrent protection hiccup current limit threshold range, % of i out rated 110 - 140% ovp trip range 115 - 140% v out nom. remote shutdown reference v in negative shutdown pin current, sourced at off 10 ma max. output general turn-on time 10 ms remote shutdown positive/negative logic switching frequency 250 khz isolation input - output 1500 vdc input - case 1050 vdc output - case 500 vdc temperature coefficient 0.03%/c case temperature operating range -40 to +100 c storage range -40 to +125 c humidity max., non-condensing 95% vibration, 3 axes, 5 min each 5 g, 10 - 55 hz mtbf ? (bellcore tr-nwt-000332) 2.5 x 10 6 hrs safety ul, cul, tuv weight (approx.) 1.4 oz 50 55 60 65 70 75 80 85 90 95 10 20 30 40 50 60 70 80 90 100 load % efficiency % has030zh-a has030zg-a has030zj-a has030yg-a 60 65 70 75 80 85 90 10 20 30 40 50 60 70 80 90 100 load % efficiency % eff. (18v) eff. (24v) eff. (36v) efficiency vs. load (48v input) efficiency vs. load (24v input) notes ? mtbf predictions may vary slightly from model to model. specifications typically at 25 c, normal line, and full load, unless otherwise stated. soldering conditions: i/o pins, 260 c, ten seconds; fully compatible with commercial wave-soldering equipment. safety: agency approvals may vary from model to model. please consult factory for specific model information. units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. has30 dc-dc series data sheet rev. feb 01, 2006 page 1 of 3 www.power-one.com
model input voltage input voltage maximum input output rated output ripple & noise typical (volts) range (volts) current (amps)* voltage (volts) current (amps) pk-pk (mv) efficiency** has030yg-a 24 18-36 2.2 5 6.0 100 83% has030yh-a 24 18-36 2.2 12 2.5 150 87% has030yj-a 24 18-36 2.2 15 2.0 150 86% has030ze-at 48 36-75 1.0 3.3 6.0 100 81% has030zg-a 48 36-75 1.3 5 6.0 100 83% has030zh-a 48 36-75 1.3 12 2.5 150 88% has030zj-a 48 36-75 1.3 15 2.0 150 88% notes: * maximum input current at minimum input voltage, maximum rated output power. ** at nominal v in , rated output. model selection mechanical drawing 1 2 3 4 5 6 7 8 9 0.700"(17.8mm) 1.400"(35.6mm) 1.000"(25.4mm) 0.400"(10.2mm) 0 0.18" 2.28" (57.9mm) dia 0.040" 0.025" ref. 0.50" (12.7mm) (4.6mm) (1.0mm) mounting inserts m3x.5 through 4pl (0.6mm) bottom view 1.700"(43.2mm) -0.50"(-12.7mm) -0.300"(-7.6mm) -0.300"(-7.6mm) 1.400"(35.6mm) 1.000"(25.4mm) 0.400"(10.2mm) 0 0 (-4.8mm) -0.19" (48.3mm) 1.900" (61.0mm) 2.40 " thermal impedance natural convection 7.9 c/w 100 lfm 6.8 c/w 200 lfm 4.9 c/w 300 lfm 3.6 c/w 400 lfm 3.0 c/w tolerances note: thermal impedance data is dependent on many environmental factors. the exact thermal performance should be validated for specific application. 1-v in 2 case 3 on/off 4+v in 5-v out 6 -sense 7 trim 8 +sense 9+v out inches: (millimeters) .xx 0.020 .x 0.5 .xxx 0.010 .xx 0.25 pin: 0.002 0.05 (dimensions as listed unless otherwise specified.) pin function has30 dc-dc series data sheet rev. feb 01, 2006 page 2 of 3 www.power-one.com model numbers highlighted in yellow or shaded are not recommended for new designs. nuclear and medical applications - power-one products are not designed, intended for use in, or authorized for use as critical c omponents in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written conse nt of the respective divisional president of power-one, inc. technical revisions - the appearance of products, including safety agency certifications pictured on labels, may change dependin g on the date manufactured. specifications are subject to change without notice.
options rev. feb 01, 2006 page 3 of 3 www.power-one.com series applicability: has, hbd, hbs, hes, qbs, qes, tes, tqd features & options descriptions suffix code remote on/off positive logic none negative logic n trim standard power-one (negative) none industry-standard (positive) t pin length 0.18? (4.6mm), standard model length none 0.145? (3.68mm) 7 0.110? (2.8mm) 8 special options customer-specific models s# note: contact factory for availability of specific options. ordering information suffix code identification:
|
